Delta Club 82 école de deltaplane près de Toulouse Montauban
Apprendre à voler en deltaplane - Trouver une école de deltaplane
Baptême de l'air en deltaplane près de Toulouse Montauban
Météo vol libre
Bibliotheque du Deltaplane
Photos de deltaplane
Vidéo deltaplane
Sites de vol libre
Occasion vol libre : deltaplane, parapente...
Les ailes et les fabricants de deltaplane
Forum du deltaplane


Le Delta CLub 82 est aussi sur Facebook
Ecole de deltaplane dans la région de Toulouse - MontaubanAgendaDivers deltaplane et vol libreDelta Club 82 Ecole de deltaplane

>>> Hang glider QUICKSILVER


Bible home » Hang glider : Quicksilver

If you have additional information (ex: specificity of piloting, various characteristics...) on the hang glider Quicksilver by Cronk Gygax, you can supplement his card by adding your comment or write to us :

Hang glider card : Quicksilver
Name :
QUICKSILVER
Manufacturer :
Cronk Gygax
Year :
1972
Pilot level :
Advanced pilots
Manual :
-
Document(s) :
-
 
Hang glider model :
A
B
Wing area (m²) :
10.80
15
Wing span(m) :
9.15
10.43
Aspect ratio :
7.75
6.40
Hang glider weight (kg) :
25
32
Minimum pilot weight (kg) :
50
55
Maximum pilot weight (kg) :
80
110
Minimum speed (km/h) :
35
30
Maximum speed (km/h) :
50
55
Max glide ratio (L/H) :
7
8
Max glide ratio speed (km/h) :
     -
42
Minimum sink rate (m/s) :
1.30
1.30
Packed length (m) :
4.50
5.30
Packed length short (m) :
-
-
Number of battens :
-
-
Nose angle (°) :
180
180

Comments

 
24/09/2005

Commentaires trouvés sur le net :
"In the early 1970s the direction of hang gliding's technical evolution was unclear. The Quicksilver was a 'semi rigid' type with a rudder connected to the seat harness. Together with its dihedral this effected turns.
When the pilot applied sideways weight shift, lines connected to the seat harness and routed through pulleys mounted under the wings, activated the rudder.

Although in hang gliding the Quicksilver was never as popular as the rogallo, in the 1970s and 80s it became an important branch in the evolutionary tree of powered ultralights.

Mark Clarkson, flying a Quicksilver in the spring of 1974, flew seventeen miles (measured as a straight line between take-off and landing). The farthest anyone had flown in a hang glider."



 
24/11/2005
[Translation of the original French comment]
Here a letter found on the Net which is an incredible source of information recalling the history of Quicksilvers since their beginning... Bonne reading!!!

"The origin of the Quicksilver can be found in Bob Lovejoy's High-Tailer (sp?) design. The High-Tailer and early Quicksilvers all had a 4 foot chord and 30 ft span. IIRC, the High-Tailer had swept twin vertical fins that started at the control bar, passed the trailing edge of the wing (mostly the same as the original Quicksilver) and ended somewhat above the wing. A horizontal tail capped the two verticals off. Again, IIRC, the design had some directional control problems (it would almost always fly straight ahead, very stable), and the control bar/vertical/horizontal arrangement was somewhat flexible. It was a four sides parallelogram structure, so had little inherent stiffness.

The original Quicksilver (later called the "A" model) was built from the High-Tailer. The twin verticals and high mounted horizontal were replaced with an "A" frame off the trailing edge of the wing, back to a fixed horizontal and a "C" frame rudder (no fixed fin). As the trailing edge of the "C" frame was unsupported, the rudder distorted a
lot, but it was very effective at directional control, and the glider responded through dihedral effect (Cl-beta). The "C" frame rudder got replaced with a different "D" frame rudder which solved the distortion problem.

I can't recall if it was Dave Cronk or Bob Lovejoy (or one of the other Eipper guys) that first thought to load test the Quicksilver. in any case, the failure occured at very low G (again, fuzzy memory, IIRC it was about 3.5 Gs), between the trailing edge flying wire and the center section. Also, the single upper wire to the tail didn't
provide much lateral support to the rudder loads. These led to the to the first improved model of the Quicksilver, called the "B." A wire was added from the control bar to the trailing edge of the wing (increasing the G limit to about 5.5), the "A" frame of the tail group gained a straight section between the horizontal and the rudder
(making a square "U" section) and a second upper wire was added from the kingpost to the tail (one wire to each end of the squared-off "U"). The result was the best of the early model Quicksilvers, as a flying machine and structurally.

The next Quicksilver improvement was increasing the span (from 30 ft to 32 ft), increasing the chord (from 4 ft to 5 ft), and enlarging the tail (the rudder lost it's characteristic "swept" leading edge). The wing also gained square tips (cf the "tapered" tip of the HT/QsA/QsB) to make the Quicksilver C model. This model also had a much reduced camber of the airfoil (the High-Tailer through Quicksilver B model had a "670-15" airfoil, which was made by bending a thin aluminum tube for one-half of it's length over a 670-15 car tire; it was about 12% camber; the C and later models had about an 8% camber, again, IIRC). This was the same model that Jack Schroeder and
Dave Cronk flew in the (much delayed) 1974 Nationals (I believe that Bill Liscomb was still flying an older B model at that meet). The C model seemed to be the most prolific of the hang glider models.

There after, there were some experimental models meant to improve performance. And here the letter designations get very fuzzy. All HT and Qs models to this point had a tube for a trailing edge. I don't know if it was Cronk, or Lovejoy, or one of the other Eipper guys, but an experiment was made of moving the trailing edge spar forward, and
making a thin trailing edge of fabric only. The leading edge pocket was also made VERY large (maybe about 50% of the chord). When I talked to Dave Cronk about this, he said it ruined the stall characteristics (very sharp and abrupt), but penetration went WAY up. this may have been called a "D" model. But I do know that later still
the leading edge pocket was made even larger to enclose the leading AND trailing edge spars (about 80%) making a double surface airfoil. This model (the "E"?) was a rocket in Cronk's hands, though I don't think any were sold to customers. This would have been about the time of the first Fledge IIBs appearing in California with a similar pocket enclosing the spars (I don't know who did it first, or who copied who, or even if both came up with it independently of each other; I would guess the last option being the most probable).

There were some competitors out there as well. Conquest was one (very high level of fit and finsh on these). Another (much less successful) was the Condor. The Qs was certainly the "performance" machine of the
day until surpassed by Fledges. And the Rogallos started improving in this same time frame, Mike Riggs' Seagull V, Rich Finley's Windlord, Tom Peghiny's Peregrine, and Roy Haggard's (unbelievably radical) Dragonfly. Once you compute the transport and set-up hassles against the performance gain, the flexwings were more than competitive to most buyers.

It's funny how things have come full circle. Now with Exxtasy, Ixbo, ATOS, and Millenium rigid wings easy to set-up and almost as easy to transport as flexwings, we're nearly back to parity again (complexity and weight still favor the modern flexwing). And I still get out my plans for the Quicksilver A/B once in a while and look at them. I
have many fond memories watching Pat Conniry and Dave Cronk flying their Quicksilvers at Torrance Beach. And helping my friend, Sandy Klevans, set-up, launch and fly his Quicksilver...

Al Bowers "


 
07/03/2010

I remember the 800 hill in telluride co where david launched one day and flew the ridge all the way to town and back. quite the flight. not much on the early flights in t-ride.


 
12/09/2010

me gusta mucho este planeador y como fue creado en el año en que yo naci me gustaria que me facilitaran lod planos para construirme uno gracias


 
01/10/2010

i had plans of an early bob lovejoy quicksilver hanglider i the 1970's but i lost them but if up would answer my letter ,i believe some one out there would be able to put the plans o the net .


 
17/10/2010

Escribe texto o la dirección de un sitio web o traduce un documento.
Cancelar
Escuchartraducción del español al inglés
hello friends I would like someone who has the plans for this beautiful glider I send them to my email  
thanks...